BS-K flotation machine
[Catalog:Flotation equipment] [Date:2017-11-7 12:08:25] [Hits:] [Return]
Features
The main shaft of BS-K flotation machine is hung at one side of the frame. With a light structure, it’s easy to install the bearing body with a good perpendicularity. With cone-shaped cross section of the impeller and radiation-shaped stator, the machine is featured with wear resistance, long service life and powerful agitating force. U-shaped tank reduces the ore accumulated at the bottom of the tank. With light main shaft parts and the stator installed at the bottom of the tank, it’s easy to install them. With small installed power, the machine is energy saving. With compressed air filled in, air bubbles disperse uniformly and the foam is stale. Thus, the suspension of mineral grains is good with a high recovery rate.
This product can be divided into several units, such as single tank, double tank, three tanks, four tanks, five tanks and six tanks, etc. Since this product has no ability of imbibing the ore pulp and air spontaneously, the flow of ore pulp needs terrace arrangement, and the return of foams depends on the foam pump.
- Notes for Selection
While placing your order, in addition to specifying the model and quantity, make sure to provide the flotation circuit and the followings
Configuration scheme and feeding mode
Quantity of the scrapers and mode of drive (right drive or left drive)
Quantities of feeding chambers, intermediate chambers, and crude ore chambers
Other special requirements.
No electric control cabinet will be supplied.
The flashboard will be made according to the manufacturer’s drawings. And the electric driven flashboard will be adopted for large-scale flotation machine.
The main shaft of BS-K flotation machine is hung at one side of the frame. With a light structure, it’s easy to install the bearing body with a good perpendicularity. With cone-shaped cross section of the impeller and radiation-shaped stator, the machine is featured with wear resistance, long service life and powerful agitating force. U-shaped tank reduces the ore accumulated at the bottom of the tank. With light main shaft parts and the stator installed at the bottom of the tank, it’s easy to install them. With small installed power, the machine is energy saving. With compressed air filled in, air bubbles disperse uniformly and the foam is stale. Thus, the suspension of mineral grains is good with a high recovery rate.
This product can be divided into several units, such as single tank, double tank, three tanks, four tanks, five tanks and six tanks, etc. Since this product has no ability of imbibing the ore pulp and air spontaneously, the flow of ore pulp needs terrace arrangement, and the return of foams depends on the foam pump.
- Notes for Selection
While placing your order, in addition to specifying the model and quantity, make sure to provide the flotation circuit and the followings
Configuration scheme and feeding mode
Quantity of the scrapers and mode of drive (right drive or left drive)
Quantities of feeding chambers, intermediate chambers, and crude ore chambers
Other special requirements.
No electric control cabinet will be supplied.
The flashboard will be made according to the manufacturer’s drawings. And the electric driven flashboard will be adopted for large-scale flotation machine.
| Model | (m3) Volume | (r/min) Rotational of rotor | (MPa) Wind pressure | (m3/ min) Processing capacity | Motor Power |
(mm) Inner Dimension |
Weight of single cell |
| BS-K2.8 | 2.8 | 248 | 0.015 | 0.4~3 | Y160M2-8/5.5 | 1550×1550×1350 | 1740 |
| BS-K4 | 4.0 | 210 | 0.5~4 | Y160L-8/7.5 | 1850×1850×1550 | 2568 | |
| BS-K8 | 8.0 | 180 | 1.0~8.0 | Y180L-6/15 | 2350×2350×1950 | 4460 | |
| BS-K16 | 16.0 | 160 | 2.0~15.0 | Y250M-8/30 | 2800×2800×2400 | 9231 | |
| BS-K24 | 24.0 | 154 | 7~20 | Y280S-8/37 | 3200×3200×2800 | 11107 |
